| |
|
Products/Tailgate loaders
MODELS:
ATK |
MTK
/ HTK |
UTK |
 |
 |
 |
| Platform must be folded one time and then it will be
moved 180 degrees to rest on the lifting arms. |
This is the simplest model with the lowest weight.
The platform is normally one piece but it could be a two piece platform
that travels behind the doors. |
Completely ready to install, including the sliding
cylinder. The installation is very quick like our other new models.
If an electrical short occurs, the platform can still be moved,
to the travel position, because of the gas cylinder. The power pack
is very simple and easy to maintain. |
Perfection in every detail:
The new AHT range of liftgates consists of a more cost effective two
and three cylinder system compared to the well known 4 cylinder models.
The newest models were designed for small vehicles with a short overhang
and low bed height. This also helps to increase the payload of the vehicle.
All new models are completely mounted, adjusted and tested before leaving
the factory. The installation is very quick. No welding is required as
the mounting brackets simply slide into place. Drill 8 holes and install
the bolts.
Weight
Less weight means more payload and more payload means more income.
AHT high strength aluminum profiles are extremely light in weight.
Example.: ATK-500ST/AL without underrun beam, ready for work,
incl. mounting material: 173kg.
|
|
 |
Power Pack
- Compact design can be mounted on the left or right side of vehicle
- Two button remote control for Up and Down operation
- Hydraulic system is only used to lift up the platform
- Two hand safety control |
| |
|
|
| |
| |
All-Aluminum Cylinders
- Ceramic coated pistons are standard
- Extremely long life span
- Tested for more than 800 thousand cycles without
changing seals.
- Noiseless operation at all temperature ranges
- Resistance against salt water and other aggressive
fluids
|
| |
| |
|
|
|
Mounting bracket
The mounting brackets can be moved on the crossbeam of the tailgate
loader, so a simple and quick installation without welding is possible.
|
|
Long life and low maintenance
|
|
| |
|
| - |
Cylinders are equipped with mechanical hose
burst valves to protect the driver and goods during lifting and lowering
of the platform. |
| - |
The platform will stop immediately, if a hose
breaks, so the operator will not be injured and the goods are protected. |
| - |
The 2-button control is equipped with a pull
out protector to prevent an electrical short and also to protect the
uncontrollable movement of the platform. |
 |
Tailgate loader: UTK-750ST/AL
An very short tandem cylinder allows installation even if the vehicle
overhang is short. |
|
Miscellaneous Items
- No electronic parts
- All steel parts are powdered coated
- One size hydraulic hoses
- Chrome plated bolts with DU Bearings
- All brackets and screws are made of Stainless Steel
Options
- Three button Foot Control
- Flashing Lights
- Roll Stops |
The continous aluminum hinge is guided by a stainless
steel rod that has a grease fitting at every section.
|
| |
|
ATK-Model |
Mechanism |
Platform |
Capacity
kg |
Load
centre
mm |
Platform Size
W x L mm |
Weight
kg |
ATK-500ST/ST |
Steel |
Steel |
500 |
500 |
1525x940 |
212 |
| ATK-500ST/AL |
Steel |
Aluminum |
500 |
500 |
1525x940 |
173 |
| ATK-500AL/AL |
Aluminum |
Aluminum |
500 |
500 |
1525x940 |
135 |
| ATK-750ST/ST |
Steel |
Steel |
750 |
500 |
1800x940 |
236 |
ATK-750ST/AL |
Steel |
Aluminum |
750 |
500 |
1800x1200 |
203 |
ATK-750AL/AL |
Aluminum |
Aluminum |
750 |
500 |
1800x1200 |
145 |
ATK-1000ST/AL |
Steel |
Aluminum |
1000 |
500 |
2200x1150 |
247 |
ATK-1000AL/AL |
Aluminum |
Aluminum |
1000 |
500 |
2200x1150 |
183 |
|
MTK-Model |
Mechanism |
Platform |
Capacity
kg |
Load
centre
mm |
Platform Size
W x L mm |
Weight
kg |
MTK-500ST/M |
Steel |
Steel Mesh |
500 |
500 |
1750x950 |
210 |
| MTK-500ST/AL |
Steel |
Aluminum |
500 |
500 |
1750x950 |
185 |
| MTK-500AL/AL |
Aluminum |
Aluminum |
500 |
500 |
1750x950 |
140 |
| MTK-750ST/M |
Steel |
Steel Mesh |
750 |
500 |
1750x1250 |
246 |
MTK-750ST/AL |
Steel |
Aluminum |
750 |
500 |
2100x1250 |
221 |
MTK-750AL/AL |
Aluminum |
Aluminum |
750 |
500 |
2100x1250 |
157 |
MTK-1000ST/AL |
Steel |
Aluminum |
1000 |
500 |
2000x1250 |
237 |
MTK-1000AL/AL |
Aluminum |
Aluminum |
1000 |
500 |
2000x1250 |
177 |
|
UTK-Model |
Mechanism |
Platform |
Capacity
kg |
Load
centre
mm |
Platform
Size
W x L mm |
Weight
kg |
UTK-500ST/ST |
Steel |
Steel |
500 |
500 |
1525x940 |
240 |
| UTK-500ST/AL |
Steel |
Aluminum |
500 |
500 |
1525x940 |
215 |
| UTK-500AL/AL |
Aluminum |
Aluminum |
500 |
500 |
1525x940 |
175 |
| UTK-750ST/ST |
Steel |
Steel |
750 |
500 |
1800x940 |
244 |
UTK-750ST/AL |
Steel |
Aluminum |
750 |
500 |
1800x1200 |
228 |
UTK-750AL/AL |
Aluminum |
Aluminum |
750 |
500 |
1800x1200 |
203 |
UTK-1000ST/AL |
Steel |
Aluminum |
1000 |
500 |
2200x1500 |
322 |
UTK-1000AL/AL |
Aluminum |
Aluminum |
1000 |
500 |
2200x1500 |
275 |
UTK-1500ST/AL |
Steel |
Aluminum |
|
500 |
2200x1700 |
460 |
UTK-2000ST/AL |
Steel |
Aluminum |
2000 |
800 |
2200x1700 |
578 |
| ANIMATION
OF THE ATK-TAILGATE LOADER (Hydraulic Schematic
and Movement) |
| |
Click on image to enlarge |
Click on image to enlarge |
Tailgate Loader-Model: ATK
Underrun beam: No
Hose Burst Valve: mechanical
|
Tailgate Loader-Model: ATK
Underrun Beam: Yes
Hose Burst Valve: Electrical
|
|
|
